Digital metering for current transformers
By EPR Magazine Editorial January 9, 2020 12:45 pm
By EPR Magazine Editorial January 9, 2020 12:45 pm
NANO 3 PHASE CT
Abstract: With the advent of smart technologies, digital metering has gained popularity in the field of measurement and control. It becomes unnecessary to use large current inputs for digital meters and in order to reduce size and cost, CTs with compact size and low output current ratings in the range of milli amperes (mA) are manufactured. These are called nano CTs, due to their compact appearance and mA output, making them most suitable for modular panel applications.
Introduction
Current transformers
According to IEC 61869-2, a current transformer is in which the secondary current, under normal conditions of use, is substantially proportional to primary current and differs in phase from it by an angle which is approximately zero for an appropriate direction of the connections.
Working principle
Current transformers reduce high magnitude currents to a much lower value and provide a convenient way of safely monitoring the actual electrical
The principle of operation of a basic current transformer is slightly different from that of an ordinary voltage transformer.
It consists of only one or very few turns as its primary winding. The primary winding can be of either a single flat turn, a coil of heavy duty wire wrapped around the core or just a conductor or bus bar placed through a central hole as shown. Due to this type of arrangement it is to be connected in series with the conductor carrying load current.
A current transformer, like any other transformer, must satisfy the amp-turn equation and as we know this turns ratio is equal to:
Current flowing in an AC circuit which is carrying high current with the help of an ammeter.
For example, the current rating of the primary winding is 125A. The secondary winding has the standard rating of 5A. Then the ratio between the primary and the secondary currents is 125A to 5A, or 25:1. In other words, the primary current is 25 times greater than the secondary current.
Current transformers are used extensively for measuring current and monitoring the operation of the power grid and these monitoring circuits are generally rated for low input currents. Hence the secondary of a CT has a rated current of 1A or 5A.
Often, multiple CTs are installed for various uses. For example, protection devices and revenue metering may use separate CTs to provide necessary current inputs to the respective systems. For isolation between metering and protection circuits current transformers with different characteristics (accuracy, overload performance) are used.
Special Purpose Current Transformers:
Generally the current transformers used have rated secondary of 5A or 1A. But due to the implementation of ‘Smart Systems’ like PLCs, Modular Control Panels, Branch Circuit Monitoring, Remote Terminal Units , Power Distribution Units and control systems the requirement of special types of CTs has become apparent.
Some of them are follows:
Rish Nano CT:
Current transformers finds its application in the field of measurement & protection such as Power Control Centers, Motor Control Centers, switch-gear and protection systems.
But due the increase in consumption of electrical energy and the widespread awareness of energy efficiency, there has been a boost in the implementation of monitoring and analysing devices which include bulky high power consuming instrument transformers, increasing the system complexities regarding space, hard-wiring and fault detection.
Thene win novative Nano3- phaseCT offers significant advantages to professionals during the power analysis and meter implementation and installation phase in electrical panels, mitigating the afore mentioned complications.
It is a set of three compact current transformers for 63A, 125A & 250A panels.
Being a very reliable, efficient and low power consuming device with a burden of 0.1VA and secondary output of 100mA, it can be used to measure current of various devices in modular control panels.
Here are some of the product features at a glance:Areas of Application:
The compact and robust design with an output of 100mA makes Nano CT suitable for a number of low current applications.
Motor Control Centers(MCC):
Motor control centers are an assembly which houses a combination of motor control units.
These include switching & protection devices like thermal overload relays, circuit breakers and motor starters and meters for current and voltage monitoring.
For 3 phase higher horse power motors, meters used are fed through CTs. Nano CT can be used for the measuring & indication in MCC. This gives added benefits of:
Branch circuit monitoring:
Branch Circuit Monitoring (BCM) system allows us to fully utilize a power infrastructure and manage capacity as your data center grows and changes.
Different critical areas of a plant are monitored and their electrical parameters are displayed using digital panel meters.
Rish Nano 3 phase CT suit well for such applications. In this case the meters must be calibrated and tested for mA current inputs and display currents in Amperes.
The above mentioned features and technical details makes Rish Nano three-phase CT perfect for compact and modular applications.
For more details please contact:
Ms. Neha Mistri
Application Engineer
Rishabh Instruments Pvt.Ltd.
We use cookies to personalize your experience. By continuing to visit this website you agree to our Terms & Conditions, Privacy Policy and Cookie Policy.